Ignition pickup and tacho sensor

Connector plug has two male spades. Also known as phase sensor. Used on models with the large Marelli P8 ECU. No longer available from Guzzi. Note 90° angle where cable exits sensor. See ENA90141 for O ring used to fit this part

 1 in stock

 29721660 GU29721660 29 72 16 60
 2972 1660 2972.1660 29.72.16.60

Marelli air temperature sensor

Supplied with screws. Two required per engine

 Order now and we will post your order within 7 days.

 30729330 GU30729330 30 72 93 30
 3072 9330 3072.9330 30.72.93.30

Neutral switch

Also known as Guzzi ref. 19207200

 This part is due back in stock soon, call 01484 841395 to reserve yours

 19207220 GU19207220 19 20 72 20
 1920 7220 1920.7220 19.20.72.20

Domino left hand switchgear with lights on - park - off, high and low beam, pass, indicator and horn switches. Same style switch as ELA01738.

Already wired in to 9 pin block connector (you may need to alter the wiring on your bike to correspond to this block connector). Originally fitted as standard to early V11 Sport models. See the wiring diagram on our technical documents page for help installing this switchgear. See Greg Bender's website for a custom sub-loom that enables easy fitting of this part to models previously fitted with LEGO style swithgear

 1 in stock

 01738030 GU01738030 01 73 80 30
 0173 8030 0173.8030 01.73.80.30

Left hand Domino type switchgear with high and low beam, pass, indicator and horn switches. Same style switch as ELA01738

On most bikes this will not plug directly into the wiring loom, you will need to match the wires to your loom. An indication of wire colours is supplied with this switchgear. Supplied with 9 pin block connector. NB does not have lights off - park - on function, you need this to be on your RH switch (e.g. ELA01729 ) or run lights always on

 This part is available by special order, request a quote

Twin output 12 volt coil used on late Guzzis

Sometimes referred to as the 'square coil', two required per bike. See ELA00001 for crimp on HT lead connector

 This part is available by special order, request a quote

 05716530 GU05716530 05 71 65 30
 0571 6530 0571.6530 05.71.65.30

High performance Quadflex maintenance free AGM Motobatt 12 volt 19Ah battery. Quadflex technology means you have two positive and two negative threaded terminals allowing maximum flexibility when installing. Motobatt absorbed gel matting batteries feature the latest absorbent glass mat technology. This offers increased lifespan, higher vibration resistance and electrical performance. This battery is also leak, vibration and spill proof if installed correctly
Suitable as a replacement for Guzzi ref. 03704571. If fitted to CARC models the top battery securing bracket will need to be omitted or modified as this battery has a different profile to the OE Yuasa battery.

Supplied charged and ready to fit, Motobatt Quadflex batteries produce 20% more cranking power (250 CCA) and are spill proof. This battery is physically smaller than the original battery fitted to some V35, V50 and V65 models, it may require packing out in the battery compartment.
NB This battery must not be trickle charged or charged using a traditional manual charger, AGM batteries require a smart charger - we recommend ACA96000
For more information on charging AGM batteries see these FAQ's.
Can also be used to replace Odyssey PC925L where a bike is in regular use (this battery should be installed on its side).

One year warranty on all our Motobatt batteries

Also available at the same price in black by special order - call 01484 841395 to order

Please note this part CANNOT be posted outside of the UK mainland area

 Availability varies on this part, check availability

 883818 MG883818

TPS for throttle body

On Cali 1100 check which TPS you have (varies according to ECU)

 2 in stock

 01530500 GU01530500 01 53 05 00
 0153 0500 0153.0500 01.53.05.00

Timing sensor for ignition and tacho

3 pin block connector. Used on models with the smaller 15M ECU

 2 in stock

 01721600 GU01721600 01 72 16 00
 0172 1600 0172.1600 01.72.16.00

Lambda sensor. Wiring harness may be shorter that your existing connector on some modeels, and will therefore need extending.

 This part is available by special order, request a quote

 32727010 GU32727010 32 72 70 10
 3272 7010 3272.7010 32.72.70.10